Silicone sealers with non-stick properties
from 112,23 € incl. VAT.
plus shipping costs
Weight | N/A |
---|---|
Container size | 1 Liter, 5 Liter, 10 Liter |
Dichtol HTR HS AS (High Temperature Resistant High Solid Anti Stick) is a highly capillary-active polymer mixture based on silicone resin with non-stick properties. The low-viscosity system was developed to penetrate very deeply into porous structures by capillary force and to seal them gas- and liquid-tight. A special additive is used to adjust the material so that it has a very low surface energy and thus minimizes the adhesion of dirt and impurities. The capillary deep impregnation or sealing with dichtol HTR HS AS is resistant up to a maximum temperature of +500°C. Dichtol HTR HS AS is a concentrated 1-component system with a solids content of >98% and is therefore considered a solvent-free system according to VdL-RL04. The high solids content promises long-lasting and reliable corrosion protection.
Properties
Temperature resistance up to +500°C
Silicone resin base offers good electrical insulating properties
Low surface energy = good non-stick properties
Very high solids content >98%
Fast curing at room temperature / no tempering or heating necessary!
Solvent-free system according to VdL-RL 04
Easy application, ready to use
Very good penetration behavior (proven up to 80% in LDS layers)
Typical applications
Capillary deep impregnation of porous structures as well as micropores and hairline cracks
Impregnation of leaking cast parts and metallic structures
Sealing
Storage / Shelf life
Store in the original, unopened container in a dry, cool and frost-free place (+5°C to +20°C). Shelf life 1 year.
Processing / Preparation
The pores to be sealed must be clean and dry. Make sure that there are no dirt residues or foreign bodies (e.g. crack sealant) in the pores, as these can negatively affect the penetration behavior of the sealer. We recommend DIAMANT Cleaner #1417 for cleaning dirty surfaces.
Application
The product is a 1-component system. Please observe the application temperatures specified in the technical data. Application on surfaces that are too warm can have a negative effect on the penetration behavior of the sealer, as can application at temperatures that are too low.
Brushing & spraying
Apply dichtol HTR HS AS in several coats and ensure that the surface to be sealed is covered with a liquid film for at least 5 minutes.
Injecting & pouring
In the case of cooling channels or threaded holes, it has proven useful to inject Dichtol HTR HS AS into the channel and allow it to react for at least 5 minutes. If necessary, remove excess material after the reaction time.
Immersion
Immerse the component to be treated in Dichtol HTR HS AS and remove it again after an exposure time of at least 5 minutes. Please ensure that the component drips off properly. It is recommended to move the component while dripping to prevent deposits from forming in undercuts or cavities.
Curing
Dichtol HTR HS AS dries under room conditions and cures in the presence of humidity. Curing can be accelerated by temperature.
You need to load content from reCAPTCHA to submit the form. Please note that doing so will share data with third-party providers.
More InformationDIAMANT Polymer GmbH
Marie-Bernays-Ring 3a
D – 41199 Mönchengladbach
Phone: +49 2166 9836-0
Fax: +49 2166 83025
Our offer is aimed exclusively at entrepreneurs and tradespeople.
You need to load content from reCAPTCHA to submit the form. Please note that doing so will share data with third-party providers.
More InformationYou need to load content from reCAPTCHA to submit the form. Please note that doing so will share data with third-party providers.
More InformationYou need to load content from reCAPTCHA to submit the form. Please note that doing so will share data with third-party providers.
More InformationYou are currently viewing a placeholder content from TrustIndex. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
More Information